Induction Soldering Cable to Metallic Plate

Objective The purpose of this test is to demonstrate the induction soldering cable to metallic plate process. Recommended Equipment The recommended equipment for this test is the DW-UHF-6kw-I handheld induction heater.

Key Parameters Power: Up to 0.72 kW Temperature: 482°F (250°C) Time: 4.5 seconds to 14 seconds

Results and Conclusions: The results were satisfactory at 14 seconds. The complete process can be achieved in less than 5 seconds by increasing the frequency from under 200 kHz to over 300 kHz, as well as by increasing the induction heating power

https://dw-inductionheater.com/induction-soldering-cable-to-metallic-plate.html?feed_id=239159&_unique_id=66072ec213f44

Induction Soldering Coaxial Cable to Connector Ring

Objective Induction Soldering coaxial cable to connector ring and pin in two steps in under 5 seconds by reaching a temperature of 500°F (260°C) with induction heating.

Equipment  DW-UHF-6KW-I handheld induction Soldering Heater Materials • No-flux solder wire • Coaxial cable • Cable connector • Center pin Key Parameters Power: 1.0kW Temperature: 662°F (350°C) Time: 5 sec

Process:

1. The coaxial cable and connector were placed vertically inside the coil.
2. Induction heating was applied for 3 seconds, at which point the part is hot enough for soldering.
3. The soldering wire was fed between the cable braid and connector.
4. Solder wire was inserted into the center pin, and the center pin was placed in the coil.
5. The cable with connector was placed above the pin.
6. Induction heating was applied for 1.5 seconds, after which the part was hot enough for soldering.
7. The center conductor was inserted into the pin.
8. The assembly was inspected to ensure that the induction soldering was successful.

Results/Benefits:

• Strong durable joints and faster heating cycles
• Selective and precise heat zone, resulting in less part distortion and joint stress
• Technology without pollution, which is both clean and safe

 

https://dw-inductionheater.com/induction-soldering-coaxial-cable-to-connector-ring.html?feed_id=239023&_unique_id=6605c12449b39

Induction Soldering Cable to Metallic Plate

Objective The purpose of this test is to demonstrate the induction soldering cable to metallic plate process. Recommended Equipment The recommended equipment for this test is the DW-UHF-6kw-I handheld induction heater.

Key Parameters Power: Up to 0.72 kW Temperature: 482°F (250°C) Time: 4.5 seconds to 14 seconds

Results and Conclusions: The results were satisfactory at 14 seconds. The complete process can be achieved in less than 5 seconds by increasing the frequency from under 200 kHz to over 300 kHz, as well as by increasing the induction heating power

Induction Soldering Cable to Metallic Plate

Objective The purpose of this test is to demonstrate the induction soldering cable to metallic plate process. Recommended Equipment The recommended equipment for this test is the DW-UHF-6kw-I handheld induction heater.

Key Parameters Power: Up to 0.72 kW Temperature: 482°F (250°C) Time: 4.5 seconds to 14 seconds

Results and Conclusions: The results were satisfactory at 14 seconds. The complete process can be achieved in less than 5 seconds by increasing the frequency from under 200 kHz to over 300 kHz, as well as by increasing the induction heating power

Induction Soldering Cable to Metallic Plate

Objective The purpose of this test is to demonstrate the induction soldering cable to metallic plate process. Recommended Equipment The recommended equipment for this test is the DW-UHF-6kw-I handheld induction heater.

Key Parameters Power: Up to 0.72 kW Temperature: 482°F (250°C) Time: 4.5 seconds to 14 seconds

Results and Conclusions: The results were satisfactory at 14 seconds. The complete process can be achieved in less than 5 seconds by increasing the frequency from under 200 kHz to over 300 kHz, as well as by increasing the induction heating power

Induction Soldering Cable to Metallic Plate

Objective The purpose of this test is to demonstrate the induction soldering cable to metallic plate process. Recommended Equipment The recommended equipment for this test is the DW-UHF-6kw-I handheld induction heater.

Key Parameters Power: Up to 0.72 kW Temperature: 482°F (250°C) Time: 4.5 seconds to 14 seconds

Results and Conclusions: The results were satisfactory at 14 seconds. The complete process can be achieved in less than 5 seconds by increasing the frequency from under 200 kHz to over 300 kHz, as well as by increasing the induction heating power

https://dw-inductionheater.com/induction-soldering-cable-to-metallic-plate.html?feed_id=222136&_unique_id=64d082955fb25

Induction Soldering Coaxial Cable to Connector Ring

Objective Induction Soldering coaxial cable to connector ring and pin in two steps in under 5 seconds by reaching a temperature of 500°F (260°C) with induction heating.

Equipment  DW-UHF-6KW-I handheld induction Soldering Heater Materials • No-flux solder wire • Coaxial cable • Cable connector • Center pin Key Parameters Power: 1.0kW Temperature: 662°F (350°C) Time: 5 sec

Process:

1. The coaxial cable and connector were placed vertically inside the coil.
2. Induction heating was applied for 3 seconds, at which point the part is hot enough for soldering.
3. The soldering wire was fed between the cable braid and connector.
4. Solder wire was inserted into the center pin, and the center pin was placed in the coil.
5. The cable with connector was placed above the pin.
6. Induction heating was applied for 1.5 seconds, after which the part was hot enough for soldering.
7. The center conductor was inserted into the pin.
8. The assembly was inspected to ensure that the induction soldering was successful.

Results/Benefits:

• Strong durable joints and faster heating cycles
• Selective and precise heat zone, resulting in less part distortion and joint stress
• Technology without pollution, which is both clean and safe

 

https://dw-inductionheater.com/induction-soldering-coaxial-cable-to-connector-ring.html?feed_id=221986&_unique_id=64cf14d567611

Induction Soldering Cable to Metallic Plate

Objective The purpose of this test is to demonstrate the induction soldering cable to metallic plate process. Recommended Equipment The recommended equipment for this test is the DW-UHF-6kw-I handheld induction heater.

Key Parameters Power: Up to 0.72 kW Temperature: 482°F (250°C) Time: 4.5 seconds to 14 seconds

Results and Conclusions: The results were satisfactory at 14 seconds. The complete process can be achieved in less than 5 seconds by increasing the frequency from under 200 kHz to over 300 kHz, as well as by increasing the induction heating power

Induction Soldering Cable to Metallic Plate

Objective The purpose of this test is to demonstrate the induction soldering cable to metallic plate process. Recommended Equipment The recommended equipment for this test is the DW-UHF-6kw-I handheld induction heater.

Key Parameters Power: Up to 0.72 kW Temperature: 482°F (250°C) Time: 4.5 seconds to 14 seconds

Results and Conclusions: The results were satisfactory at 14 seconds. The complete process can be achieved in less than 5 seconds by increasing the frequency from under 200 kHz to over 300 kHz, as well as by increasing the induction heating power

Induction Soldering Cable to Metallic Plate

Objective The purpose of this test is to demonstrate the induction soldering cable to metallic plate process. Recommended Equipment The recommended equipment for this test is the DW-UHF-6kw-I handheld induction heater.

Key Parameters Power: Up to 0.72 kW Temperature: 482°F (250°C) Time: 4.5 seconds to 14 seconds

Results and Conclusions: The results were satisfactory at 14 seconds. The complete process can be achieved in less than 5 seconds by increasing the frequency from under 200 kHz to over 300 kHz, as well as by increasing the induction heating power

Induction Soldering Coaxial Cable to Connector Ring

Objective Induction Soldering coaxial cable to connector ring and pin in two steps in under 5 seconds by reaching a temperature of 500°F (260°C) with induction heating.

Equipment  DW-UHF-6KW-I handheld induction Soldering Heater Materials • No-flux solder wire • Coaxial cable • Cable connector • Center pin Key Parameters Power: 1.0kW Temperature: 662°F (350°C) Time: 5 sec

Process:

1. The coaxial cable and connector were placed vertically inside the coil.
2. Induction heating was applied for 3 seconds, at which point the part is hot enough for soldering.
3. The soldering wire was fed between the cable braid and connector.
4. Solder wire was inserted into the center pin, and the center pin was placed in the coil.
5. The cable with connector was placed above the pin.
6. Induction heating was applied for 1.5 seconds, after which the part was hot enough for soldering.
7. The center conductor was inserted into the pin.
8. The assembly was inspected to ensure that the induction soldering was successful.

Results/Benefits:

• Strong durable joints and faster heating cycles
• Selective and precise heat zone, resulting in less part distortion and joint stress
• Technology without pollution, which is both clean and safe