2022年6月4日星期六
Heating Aluminum Foil For Cap Sealing
Induction Heating Aluminum Foil For Cap Sealing with IGBT inductive heater
Objective An induction heater is used to heat a polymer laminated aluminum foil in 0.5 to 2.0 seconds. The heat produced in the aluminum foil melts the polymer that bonds to the neck of a plastic container.
Material Aluminum foil, polyethylene, polypropylene, polyvinylchloride, polystyrene, polyethylene terephthalate, styrene acrylonitrile
Temperature 300 - 400 (ºF), 149 - 204 (ºC)
Frequency 50 to 200 kHz
Equipment DAWEI solid-state induction power supplies operating between 1 & 10 kW at frequencies of 50- 200 kHz. These units operate with remote sealing heads which allows the main power cabinet of the equipment to be located away from the immediate production area. Distances of up to 100 meters are possible. The microprocessor is used to control
and protect the system and ensures that the optimal operating frequency is maintained at all times and that each container
receives the same amount of heat energy from cycle to cycle.
Process Two different types of aluminum foil laminates are available for this application. The first assembly includes backing
board/reseal, a wax layer, aluminum foil, and a heatseal film for supported systems (Figure 1). The second assembly includes a high temperature film, aluminum foil, and a heatseal film for unsupported systems (Figure 2). The procedure is to fit the foil membrane into the cap and to fit the cap to the container after the product is filled.
Results For the aluminum foil assembly as shown in Figure 1, heat induced in the metallic foil by the induction coil almost
instantaneously melts the polymer coating and the neck of the container forming a hermetic seal between the heat seal film
and the rim of the container. The heat also melts the wax between the aluminum foil and the back board. The wax is
absorbed into the back board. This results in an air tight bond between the aluminum foil/membrane and the rim of the
container, the back board is released and remains in the cap.
Process (cont’d) In the case of unsupported membranes in Figure 2, one side of the aluminum foil is coated with a heat sealable polymer film and this face that will be in contact with and sealed to the container. The other side of the foil that will be in contact with the cap has a higher melting-point film that prevents adhesion of the aluminum to the cap allowing the end user to unscrew the cap. Unsupported membranes are typically used where the end user pierces the tamper evident membrane prior to dispensing the product. The aluminum foil acts as a vapor barrier preserving the freshness of the product and prevents it from drying.
关注者
博客归档
-
▼
2022
(1729)
-
▼
六月
(102)
- Induction Susceptor Heating
- Brazing Carbide to Steel Part With Induction Heating
- Induction Brazing Steel Parts to Tungsten Carbide ...
- Induction Brazing Brass Faucet
- Induction Brazing Stainless Steel
- What Is Induction Heating Coil&Inductor?
- Induction Brazing Steel Pipe
- Shrink Fittting Part Removal application with Indu...
- Induction Soldering Copper Pipes to PCB Board
- Induction Brazing Aluminum Pipes
- Brazing Carbide Tips To Steel With Induction
- induction brazing stainless steel to steel
- Induction Soldering Stainless Steel To Wire
- Induction Brazing copper wire to copper cylinder
- Automatic Induction Forging Video
- Induction Heating Automotive Motor
- Induction Brazing Principle-Theory
- Induction Annealing Aluminum PIpe
- Induction brazing aluminum pipes
- induction brazing carbide tip onto steel head teeth
- Billet Heating Furnace with Induction Heating
- Induction Brazing T Shaped Copper Tubing Assemblies
- High Frequency Induction Brazing Copper Wire
- Induction Brazing & Soldering Principle
- Induction Brazing Steel Tube
- induction Brazing copper rods to brass strips
- RPR Induction Pipeline Coating Removal
- induction curing
- Induction Soldering Brass Tube-Pipe
- Induction Brazing Basics
- Induction Heating Molding Catheter Tip
- RPR Induction Stripping-Induction Rust & Paint Coa...
- Induction Heating Plastic Catheter Tube
- Induction Hardening and tempering
- Induction Heating Basic
- Induction Soldering Fuse Caps
- Induction Annealing Stainless Steel Tubes
- Brazing Automotive Parts With Induction
- Handheld Induction Brazing Copper Tubing and Fitting
- Induction Soldering Circuit Board
- What Is Induction Melting?
- Induction Wire Heating Process Applications
- Brazing copper tube to brass fitting
- Induction Heating Molding Catheter Tip
- induction surface hardening steel screws
- Advantages of Induction Heating
- Induction Hardening Inner
- Induction Heating Coils Design and Basic PDF
- Shrink Fit Steel Gear onto Shaft
- Induction Heating Bolts
- Brazing Golf Ball With Induction
- RF Soldering Circuit Board
- Induction Brazing Steel Tube
- Induction Heating Magnetic Iron Oxide
- Induction Billets Heater Video
- What is induction annealing?
- Brazing copper tube to brass fitting
- Plastic Injection Molding with Induction Heating
- induction fluid pipe heater
- Induction Spring Heating Application
- Induction Brazing Stainless Steel
- Induction Aluminum Brazing Process
- Jointing Metal with Brazing and Welding
- Aluminum Can Recycling Furnace with induction heating
- Soldering Solar Panels With Induction
- induction small copper tubing brazing connection j...
- What is Induction Brazing?
- Induction Fluid Pipeline heating system
- Brazing Silver To Copper With Induction
- RF Soldering Circuit Board
- Brazing Copper Tube to Brass Fitting With Induction
- Induction annealing copper wires
- Induction Soldering Copper Pipes to PCB Board
- Induction Brazing copper wire to copper cylinder
- Induction Soldering Brass Heating Exchanger
- Brazing Cutting Tool with Induction
- Induction Heating Bolts
- Induction Soldering Brass Connector
- What is induction annealing?
- Annealing Saw Blades with Induction
- Plastic Injection Molding with Induction Heating
- Induction Shrink Fitting Carbide Ring
- Induction Heating Sintering Copper Powder
- Induction Brazing & Soldering Principle
- Heating Aluminum Foil For Cap Sealing
- Induction Annealing Brass Bullet Shells
- Induction Drying Grain with Induction Heating method
- Induction Annealing Aluminum PIpe
- Pipeline Coating Process
- Induction Curing Heating of Organic Coating
- Induction Heating Theory PDF
- Brazing Cutting Tool with Induction
- Induction Soldering Wires Onto Connection
- ultrasonic plastic welder for US plastic welding b...
- Electromagnetic Induction Steam Generator
- Brazing stainless steel with induction
- High Frequency Induction Brazing Copper Wire
- Induction Heating Magnetic Iron Oxide
- What is Induction Brazing?
- induction hot forming and forging process
-
▼
六月
(102)
我的简介
- HLQ induction heating machine
- HLQ induction heating machine manufacturer provides the service of induction brazing,melting,hot forming,hardening surface,annealing,shrink fitting,PWHT,etc.