induction brazing steel tube to copper tube

High Frequency Induction Brazing Steel Tube to Copper Tube

Objective The goal is to braze a steel tube to a copper tube in 60 seconds using flux and brazing alloy.

Equipment DW-UHF-10kw induction brazing heater Three turns dual diameter coil Materials • Steel tube and copper receiver • Braze alloy (CDA 681) • B-1 flux Key Parameters Temperature: Approximately 1750° F (954° C) Frequency: 148 kHz

Process:

1. The assembly section was pre-assembled and fluxed (B-1) then located in the two diameter coil with a single pre-formed alloy ring set at the interface area.
2. Alloy flow and joint completed in 60 seconds.
3. The material was cooled in water following the completion of induction brazing.
4. The joint was then cross-sectioned to validate that the brazing process had produced a strong, high quality joint.

Results/Benefits:

• Strong durable joints with induction heating
• Selective and precise heat zone, resulting in less part distortion and joint stress than welding
• Less oxidation
• Faster heating cycles
• More consistent results and suitability for large volume production, without the need for batch processing
• Safer than flame brazing

https://dw-inductionheater.com/induction-brazing-steel-tube-to-copper-tube.html?feed_id=235607&_unique_id=65e65518d8a86

induction brazing steel tube to copper tube

High Frequency Induction Brazing Steel Tube to Copper Tube

Objective The goal is to braze a steel tube to a copper tube in 60 seconds using flux and brazing alloy.

Equipment DW-UHF-10kw induction brazing heater Three turns dual diameter coil Materials • Steel tube and copper receiver • Braze alloy (CDA 681) • B-1 flux Key Parameters Temperature: Approximately 1750° F (954° C) Frequency: 148 kHz

Process:

1. The assembly section was pre-assembled and fluxed (B-1) then located in the two diameter coil with a single pre-formed alloy ring set at the interface area.
2. Alloy flow and joint completed in 60 seconds.
3. The material was cooled in water following the completion of induction brazing.
4. The joint was then cross-sectioned to validate that the brazing process had produced a strong, high quality joint.

Results/Benefits:

• Strong durable joints with induction heating
• Selective and precise heat zone, resulting in less part distortion and joint stress than welding
• Less oxidation
• Faster heating cycles
• More consistent results and suitability for large volume production, without the need for batch processing
• Safer than flame brazing

induction brazing steel tube to copper tube

High Frequency Induction Brazing Steel Tube to Copper Tube

Objective The goal is to braze a steel tube to a copper tube in 60 seconds using flux and brazing alloy.

Equipment DW-UHF-10kw induction brazing heater Three turns dual diameter coil Materials • Steel tube and copper receiver • Braze alloy (CDA 681) • B-1 flux Key Parameters Temperature: Approximately 1750° F (954° C) Frequency: 148 kHz

Process:

1. The assembly section was pre-assembled and fluxed (B-1) then located in the two diameter coil with a single pre-formed alloy ring set at the interface area.
2. Alloy flow and joint completed in 60 seconds.
3. The material was cooled in water following the completion of induction brazing.
4. The joint was then cross-sectioned to validate that the brazing process had produced a strong, high quality joint.

Results/Benefits:

• Strong durable joints with induction heating
• Selective and precise heat zone, resulting in less part distortion and joint stress than welding
• Less oxidation
• Faster heating cycles
• More consistent results and suitability for large volume production, without the need for batch processing
• Safer than flame brazing

https://dw-inductionheater.com/induction-brazing-steel-tube-to-copper-tube.html?feed_id=218611&_unique_id=64aedfb67501c

induction brazing steel tube to copper tube

High Frequency Induction Brazing Steel Tube to Copper Tube

Objective The goal is to braze a steel tube to a copper tube in 60 seconds using flux and brazing alloy.

Equipment DW-UHF-10kw induction brazing heater Three turns dual diameter coil Materials • Steel tube and copper receiver • Braze alloy (CDA 681) • B-1 flux Key Parameters Temperature: Approximately 1750° F (954° C) Frequency: 148 kHz

Process:

1. The assembly section was pre-assembled and fluxed (B-1) then located in the two diameter coil with a single pre-formed alloy ring set at the interface area.
2. Alloy flow and joint completed in 60 seconds.
3. The material was cooled in water following the completion of induction brazing.
4. The joint was then cross-sectioned to validate that the brazing process had produced a strong, high quality joint.

Results/Benefits:

• Strong durable joints with induction heating
• Selective and precise heat zone, resulting in less part distortion and joint stress than welding
• Less oxidation
• Faster heating cycles
• More consistent results and suitability for large volume production, without the need for batch processing
• Safer than flame brazing

induction brazing steel tube to copper tube

High Frequency Induction Brazing Steel Tube to Copper Tube

Objective The goal is to braze a steel tube to a copper tube in 60 seconds using flux and brazing alloy.

Equipment DW-UHF-10kw induction brazing heater Three turns dual diameter coil Materials • Steel tube and copper receiver • Braze alloy (CDA 681) • B-1 flux Key Parameters Temperature: Approximately 1750° F (954° C) Frequency: 148 kHz

Process:

1. The assembly section was pre-assembled and fluxed (B-1) then located in the two diameter coil with a single pre-formed alloy ring set at the interface area.
2. Alloy flow and joint completed in 60 seconds.
3. The material was cooled in water following the completion of induction brazing.
4. The joint was then cross-sectioned to validate that the brazing process had produced a strong, high quality joint.

Results/Benefits:

• Strong durable joints with induction heating
• Selective and precise heat zone, resulting in less part distortion and joint stress than welding
• Less oxidation
• Faster heating cycles
• More consistent results and suitability for large volume production, without the need for batch processing
• Safer than flame brazing

induction brazing steel tube to copper tube

High Frequency Induction Brazing Steel Tube to Copper Tube

Objective The goal is to braze a steel tube to a copper tube in 60 seconds using flux and brazing alloy.

Equipment DW-UHF-10kw induction brazing heater Three turns dual diameter coil Materials • Steel tube and copper receiver • Braze alloy (CDA 681) • B-1 flux Key Parameters Temperature: Approximately 1750° F (954° C) Frequency: 148 kHz

Process:

1. The assembly section was pre-assembled and fluxed (B-1) then located in the two diameter coil with a single pre-formed alloy ring set at the interface area.
2. Alloy flow and joint completed in 60 seconds.
3. The material was cooled in water following the completion of induction brazing.
4. The joint was then cross-sectioned to validate that the brazing process had produced a strong, high quality joint.

Results/Benefits:

• Strong durable joints with induction heating
• Selective and precise heat zone, resulting in less part distortion and joint stress than welding
• Less oxidation
• Faster heating cycles
• More consistent results and suitability for large volume production, without the need for batch processing
• Safer than flame brazing

induction brazing steel tube to copper tube

High Frequency Induction Brazing Steel Tube to Copper Tube

Objective The goal is to braze a steel tube to a copper tube in 60 seconds using flux and brazing alloy.

Equipment DW-UHF-10kw induction brazing heater Three turns dual diameter coil Materials • Steel tube and copper receiver • Braze alloy (CDA 681) • B-1 flux Key Parameters Temperature: Approximately 1750° F (954° C) Frequency: 148 kHz

Process:

1. The assembly section was pre-assembled and fluxed (B-1) then located in the two diameter coil with a single pre-formed alloy ring set at the interface area.
2. Alloy flow and joint completed in 60 seconds.
3. The material was cooled in water following the completion of induction brazing.
4. The joint was then cross-sectioned to validate that the brazing process had produced a strong, high quality joint.

Results/Benefits:

• Strong durable joints with induction heating
• Selective and precise heat zone, resulting in less part distortion and joint stress than welding
• Less oxidation
• Faster heating cycles
• More consistent results and suitability for large volume production, without the need for batch processing
• Safer than flame brazing

induction brazing steel tube to copper tube

High Frequency Induction Brazing Steel Tube to Copper Tube

Objective The goal is to braze a steel tube to a copper tube in 60 seconds using flux and brazing alloy.

Equipment DW-UHF-10kw induction brazing heater Three turns dual diameter coil Materials • Steel tube and copper receiver • Braze alloy (CDA 681) • B-1 flux Key Parameters Temperature: Approximately 1750° F (954° C) Frequency: 148 kHz

Process:

1. The assembly section was pre-assembled and fluxed (B-1) then located in the two diameter coil with a single pre-formed alloy ring set at the interface area.
2. Alloy flow and joint completed in 60 seconds.
3. The material was cooled in water following the completion of induction brazing.
4. The joint was then cross-sectioned to validate that the brazing process had produced a strong, high quality joint.

Results/Benefits:

• Strong durable joints with induction heating
• Selective and precise heat zone, resulting in less part distortion and joint stress than welding
• Less oxidation
• Faster heating cycles
• More consistent results and suitability for large volume production, without the need for batch processing
• Safer than flame brazing

induction brazing steel tube to copper tube

High Frequency Induction Brazing Steel Tube to Copper Tube

Objective The goal is to braze a steel tube to a copper tube in 60 seconds using flux and brazing alloy.

Equipment DW-UHF-10kw induction brazing heater Three turns dual diameter coil Materials • Steel tube and copper receiver • Braze alloy (CDA 681) • B-1 flux Key Parameters Temperature: Approximately 1750° F (954° C) Frequency: 148 kHz

Process:

1. The assembly section was pre-assembled and fluxed (B-1) then located in the two diameter coil with a single pre-formed alloy ring set at the interface area.
2. Alloy flow and joint completed in 60 seconds.
3. The material was cooled in water following the completion of induction brazing.
4. The joint was then cross-sectioned to validate that the brazing process had produced a strong, high quality joint.

Results/Benefits:

• Strong durable joints with induction heating
• Selective and precise heat zone, resulting in less part distortion and joint stress than welding
• Less oxidation
• Faster heating cycles
• More consistent results and suitability for large volume production, without the need for batch processing
• Safer than flame brazing