Induction Annealing Copper Tubes

Simultaneously Induction Annealing Copper Tubes

Objective Uniformly heat two copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment DW-HF-45kw induction heater Helical coil Material • Two copper tubes – OD: 0.69’’ (1.75 cm) – ID: 0.55’’ (1.40 cm) – Length: 5.50’’ (14.0 cm). Key Parameters Power: 35kW Temperature: 842°F (450°C) Time: 7sec

Process:

1. The two copper tubes were placed together in the coil.
2. Induction heat was applied for 8s.

Results/Benefits:

• Improved process control for uniform heating to a desired temperature
• Power on demand and rapid, consistent heat cycles
• Technology without pollution, which is both clean and safe

https://dw-inductionheater.com/simultaneously-induction-annealing-copper-tubes.html?feed_id=241666&_unique_id=661c9ae7aa198

Induction Annealing Copper Tubes

Objective Uniformly high frequency annealing copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment DW-HF-45kw induction heater Helical coil Material • Two copper tubes – OD: 0.69’’ (1.75 cm) – ID: 0.55’’ (1.40 cm) – Length: 5.50’’ (14.0 cm). Key Parameters Power: 27kW Temperature: 842°F (450°C) Time: 5 sec

Process:

1. The two copper tubes were placed together in the coil.
2. Induction heating was applied for 5s.

Results/Benefits:

• Improved process control for uniform induction heating to a desired temperature
• Power on demand and rapid, consistent heat cycles
• Technology without pollution, which is both clean and safe

https://dw-inductionheater.com/induction-annealing-copper-tubes.html?feed_id=238658&_unique_id=66039c78a290b

Induction Annealing Copper Wire

Induction Annealing Copper Wire Objective: Induction Annealing a brazing copper wire for preform production. Material: Copper Nickel Silver 2774 Alloy rod 0.070" (1.8mm) diameter. Temperature 650ºF(343.3ºC) Frequency 580 kHz Equipment: • DW-UHF-6kW-III induction heating system equipped with a remote workhead with one 1.0 μF capacitor, and a 4-20 mA input controller to aid in voltage ramping. • An induction heating coil designed and developed specifically for this application. Process A unique helical coil consisting of four consecutive coils connected in parallel with a quartz tube lining is used to heat the wire to 650ºF (343.3ºC) for annealing. Results/Benefits Induction heating provides: • Higher productivity of 27' (8.2m) per minute • Reduction in surface oxidation & scaling • Consistent, repeatable results https://dw-inductionheater.com/induction-annealing-copper-wire.html?feed_id=230796&_unique_id=65555e07d0d89

Induction Annealing Copper Wire

Induction Annealing Copper Wire Objective: Induction Annealing a brazing copper wire for preform production. Material: Copper Nickel Silver 2774 Alloy rod 0.070" (1.8mm) diameter. Temperature 650ºF(343.3ºC) Frequency 580 kHz Equipment: • DW-UHF-6kW-III induction heating system equipped with a remote workhead with one 1.0 μF capacitor, and a 4-20 mA input controller to aid in voltage ramping. • An induction heating coil designed and developed specifically for this application. Process A unique helical coil consisting of four consecutive coils connected in parallel with a quartz tube lining is used to heat the wire to 650ºF (343.3ºC) for annealing. Results/Benefits Induction heating provides: • Higher productivity of 27' (8.2m) per minute • Reduction in surface oxidation & scaling • Consistent, repeatable results

Induction Annealing Copper Tubes

Objective Uniformly high frequency annealing copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment DW-HF-45kw induction heater Helical coil Material • Two copper tubes – OD: 0.69’’ (1.75 cm) – ID: 0.55’’ (1.40 cm) – Length: 5.50’’ (14.0 cm). Key Parameters Power: 27kW Temperature: 842°F (450°C) Time: 5 sec

Process:

1. The two copper tubes were placed together in the coil.
2. Induction heating was applied for 5s.

Results/Benefits:

• Improved process control for uniform induction heating to a desired temperature
• Power on demand and rapid, consistent heat cycles
• Technology without pollution, which is both clean and safe

Induction Annealing Copper Tubes

Objective Uniformly high frequency annealing copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment DW-HF-45kw induction heater Helical coil Material • Two copper tubes – OD: 0.69’’ (1.75 cm) – ID: 0.55’’ (1.40 cm) – Length: 5.50’’ (14.0 cm). Key Parameters Power: 27kW Temperature: 842°F (450°C) Time: 5 sec

Process:

1. The two copper tubes were placed together in the coil.
2. Induction heating was applied for 5s.

Results/Benefits:

• Improved process control for uniform induction heating to a desired temperature
• Power on demand and rapid, consistent heat cycles
• Technology without pollution, which is both clean and safe

Induction Annealing Copper Tubes

Simultaneously Induction Annealing Copper Tubes

Objective Uniformly heat two copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment DW-HF-45kw induction heater Helical coil Material • Two copper tubes – OD: 0.69’’ (1.75 cm) – ID: 0.55’’ (1.40 cm) – Length: 5.50’’ (14.0 cm). Key Parameters Power: 35kW Temperature: 842°F (450°C) Time: 7sec

Process:

1. The two copper tubes were placed together in the coil.
2. Induction heat was applied for 8s.

Results/Benefits:

• Improved process control for uniform heating to a desired temperature
• Power on demand and rapid, consistent heat cycles
• Technology without pollution, which is both clean and safe

https://dw-inductionheater.com/simultaneously-induction-annealing-copper-tubes.html?feed_id=224536&_unique_id=64e5f29c7a77f

Induction Annealing Copper Tubes

Objective Uniformly high frequency annealing copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment DW-HF-45kw induction heater Helical coil Material • Two copper tubes – OD: 0.69’’ (1.75 cm) – ID: 0.55’’ (1.40 cm) – Length: 5.50’’ (14.0 cm). Key Parameters Power: 27kW Temperature: 842°F (450°C) Time: 5 sec

Process:

1. The two copper tubes were placed together in the coil.
2. Induction heating was applied for 5s.

Results/Benefits:

• Improved process control for uniform induction heating to a desired temperature
• Power on demand and rapid, consistent heat cycles
• Technology without pollution, which is both clean and safe

https://dw-inductionheater.com/induction-annealing-copper-tubes.html?feed_id=221761&_unique_id=64cc2c0bed1c7

Induction Annealing Copper Wire

Induction Annealing Copper Wire Objective: Induction Annealing a brazing copper wire for preform production. Material: Copper Nickel Silver 2774 Alloy rod 0.070" (1.8mm) diameter. Temperature 650ºF(343.3ºC) Frequency 580 kHz Equipment: • DW-UHF-6kW-III induction heating system equipped with a remote workhead with one 1.0 μF capacitor, and a 4-20 mA input controller to aid in voltage ramping. • An induction heating coil designed and developed specifically for this application. Process A unique helical coil consisting of four consecutive coils connected in parallel with a quartz tube lining is used to heat the wire to 650ºF (343.3ºC) for annealing. Results/Benefits Induction heating provides: • Higher productivity of 27' (8.2m) per minute • Reduction in surface oxidation & scaling • Consistent, repeatable results

Induction Annealing Copper Tubes

Objective Uniformly high frequency annealing copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment DW-HF-45kw induction heater Helical coil Material • Two copper tubes – OD: 0.69’’ (1.75 cm) – ID: 0.55’’ (1.40 cm) – Length: 5.50’’ (14.0 cm). Key Parameters Power: 27kW Temperature: 842°F (450°C) Time: 5 sec

Process:

1. The two copper tubes were placed together in the coil.
2. Induction heating was applied for 5s.

Results/Benefits:

• Improved process control for uniform induction heating to a desired temperature
• Power on demand and rapid, consistent heat cycles
• Technology without pollution, which is both clean and safe

Induction Annealing Copper Wire

Induction Annealing Copper Wire Objective: Induction Annealing a brazing copper wire for preform production. Material: Copper Nickel Silver 2774 Alloy rod 0.070" (1.8mm) diameter. Temperature 650ºF(343.3ºC) Frequency 580 kHz Equipment: • DW-UHF-6kW-III induction heating system equipped with a remote workhead with one 1.0 μF capacitor, and a 4-20 mA input controller to aid in voltage ramping. • An induction heating coil designed and developed specifically for this application. Process A unique helical coil consisting of four consecutive coils connected in parallel with a quartz tube lining is used to heat the wire to 650ºF (343.3ºC) for annealing. Results/Benefits Induction heating provides: • Higher productivity of 27' (8.2m) per minute • Reduction in surface oxidation & scaling • Consistent, repeatable results

Induction Annealing Copper Tubes

Objective Uniformly high frequency annealing copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment DW-HF-45kw induction heater Helical coil Material • Two copper tubes – OD: 0.69’’ (1.75 cm) – ID: 0.55’’ (1.40 cm) – Length: 5.50’’ (14.0 cm). Key Parameters Power: 27kW Temperature: 842°F (450°C) Time: 5 sec

Process:

1. The two copper tubes were placed together in the coil.
2. Induction heating was applied for 5s.

Results/Benefits:

• Improved process control for uniform induction heating to a desired temperature
• Power on demand and rapid, consistent heat cycles
• Technology without pollution, which is both clean and safe

Induction Annealing Copper Tubes

Simultaneously Induction Annealing Copper Tubes

Objective Uniformly heat two copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment DW-HF-45kw induction heater Helical coil Material • Two copper tubes – OD: 0.69’’ (1.75 cm) – ID: 0.55’’ (1.40 cm) – Length: 5.50’’ (14.0 cm). Key Parameters Power: 35kW Temperature: 842°F (450°C) Time: 7sec

Process:

1. The two copper tubes were placed together in the coil.
2. Induction heat was applied for 8s.

Results/Benefits:

• Improved process control for uniform heating to a desired temperature
• Power on demand and rapid, consistent heat cycles
• Technology without pollution, which is both clean and safe

Induction Annealing Copper Tubes

Objective
Uniformly high frequency annealing copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment
DW-HF-45kw induction heater


Helical coil

Material
• Two copper tubes
– OD: 0.69’’ (1.75 cm)
– ID: 0.55’’ (1.40 cm)
– Length: 5.50’’ (14.0 cm).

Key Parameters
Power: 27kW
Temperature: 842°F (450°C)
Time: 5 sec

Process:

1. The two copper tubes were placed together in the coil.


2. Induction heating was applied for 5s.

Results/Benefits:

• Improved process control for uniform induction heating to a desired temperature


• Power on demand and rapid, consistent heat cycles


• Technology without pollution, which is both clean and safe

Induction Annealing Copper Tubes

Objective Uniformly high frequency annealing copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment DW-HF-45kw induction heater Helical coil Material • Two copper tubes – OD: 0.69’’ (1.75 cm) – ID: 0.55’’ (1.40 cm) – Length: 5.50’’ (14.0 cm). Key Parameters Power: 27kW Temperature: 842°F (450°C) Time: 5 sec

Process:

1. The two copper tubes were placed together in the coil.
2. Induction heating was applied for 5s.

Results/Benefits:

• Improved process control for uniform induction heating to a desired temperature
• Power on demand and rapid, consistent heat cycles
• Technology without pollution, which is both clean and safe

Induction Annealing Copper Tubes

Simultaneously Induction Annealing Copper Tubes

Objective
Uniformly heat two copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment

DW-HF-45kw induction heater
Helical coil

Material
• Two copper tubes
– OD: 0.69’’ (1.75 cm)
– ID: 0.55’’ (1.40 cm)
– Length: 5.50’’ (14.0 cm).

Key Parameters
Power: 35kW
Temperature: 842°F (450°C)
Time: 7sec

Process:

1. The two copper tubes were placed together in the coil.


2. Induction heat was applied for 8s.

Results/Benefits:

• Improved process control for uniform heating to a desired temperature


• Power on demand and rapid, consistent heat cycles


• Technology without pollution, which is both clean and safe

Induction Annealing Copper Tubes

Simultaneously Induction Annealing Copper Tubes

Objective Uniformly heat two copper tubes simultaneously to 800°F (426°C) in under 10 seconds with induction heating.

Equipment DW-HF-45kw induction heater Helical coil Material • Two copper tubes – OD: 0.69’’ (1.75 cm) – ID: 0.55’’ (1.40 cm) – Length: 5.50’’ (14.0 cm). Key Parameters Power: 35kW Temperature: 842°F (450°C) Time: 7sec

Process:

1. The two copper tubes were placed together in the coil.
2. Induction heat was applied for 8s.

Results/Benefits:

• Improved process control for uniform heating to a desired temperature
• Power on demand and rapid, consistent heat cycles
• Technology without pollution, which is both clean and safe